Select Page

Product Description

1850mm track 13T FUWA/BPW/YORK/HJ commercial truck trailer axle for fuel tank/tanker trailer

Product Description

Semi-trailer axle refers to the axle assembly specially used on semi-trailer. It is a key part of the vehicle chassis. It usually includes auxiliary accessories such as axle, brake and suspension. It is connected to the trailer body through the suspension. Wheels are installed at both ends of the axle. , its main function is to carry the load of the trailer and maintain the normal driving of the vehicle.

Our lightweight axles are mainly used for powder tank semi-trailers, van semi-trailers, flatbed semi-trailers, container skeleton semi-trailers, oil tank semi-trailers, etc.

The semi-trailer axle is connected by the suspension and the frame, which plays a load-bearing role for the Xihu (West Lake) Dis. trailer. Therefore, before the vehicle runs, check whether the connecting bolts of the external structure of the axle are loose, whether the axle has oil leakage, whether the rim and reducer assembly are Not abnormal noise, etc., to ensure safety.

Semi-trailer axle maintenance:

1. On-time maintenance is performed every 10,000km after the initial maintenance.

2. The contents of regular maintenance include: replacing the lubricating oil, tightening the fasteners, checking the toe-in, checking the wear degree of the brake pads, and if the wear level is reached, it should be replaced in time and the brake gap should be adjusted, and the deceleration should be checked. Whether the gap between the main gear and the driven gear is too large, and whether the gear oil exceeds the function of use, if there is a similar situation, the gap should be adjusted and the grease should be replaced in time.

Product Parameters

Axle model:

F2571AD 

F2402 

F2404 

F2462BII

FN20DB01AA-200 

Axle type:

trailer axle

trailer axle 

trailer axle

trailer axle

trailer axle

Rated axle load:

16000kg 

13000kg 

13000kg 

16000kg 

12000kg 

Curb-weight:

398kg 

365kg 

351kg 

425kg 

 

Front Wheelbase
/rear Wheelbase:

1850mm 

1840mm 

1840mm 

1850mm 

1816mm 

Brakes:

S cam brake

S cam brake 

S cam brake 

S cam brake 

Disc brakes

Brake size:

Φ420X180 

Φ420X180 

Φ420X180 

Φ420X220 

Φ430X45 

Wheel Bolts:

 

 

 

 

10xM22x1.5 ISOmm 

Rims:

8.0V-20 inch

7.5-20inch

7.5V-20inch

8.0V-20inch 

R22.5inch

Remark:

Internal brake drum

External brake drum

External brake drum

Internal brake drum

Twin tires; disc brakes

 

Detailed Photos

Applications

The axles are mainly used on semi-trailer. It is a key component of the vehicle chassis. It usually includes auxiliary accessories such as axle, brake and suspension. It is connected to the trailer body through the suspension. The main function of the wheel is to carry the load of the trailer and maintain the normal driving of the vehicle.

The axle is directly related to the load-bearing, braking and driving of the semi-trailer. In order to fully guarantee the semi-trailer’s attendance, safety performance and economic benefits during long-distance travel, it is very important to choose a high-quality axle. Especially in some places, there are many mountain roads for long-distance transportation, the terrain is rugged, long and curved slopes are common, and the driving conditions of vehicles are severe, which puts forward higher requirements for the quality and performance of trailer axles.

Company Introduction

Packaging & Shipping

FAQ

Q. What is your terms of packing?

A: Generally, goods are sealed in ploy bags and packed in cartons and pallet or wood cases.

 

Q. What is your terms of payment?

A: T/T (deposit + balance before delivery). The photos of the products and packages can be showed before the balance done.

 

Q. What is your terms of delivery?

A: EXW, FOB, CFR, CIF.  By CZPT shipping or by air or by express, or by land.

 

Q. How about your delivery time?

A: Generally, it will take 10-30 days after the advance payment done.
The exact delivery time depends on the parts items and the quantity of your order.

 

Q. Can you produce according to the samples?

A: Yeah, we can produce by your samples and with detailed technical drawings for better. 

 

Q. What is your sample policy?

A: The sample for free charge if we have ready parts in stock, but the customs tax and courier cost shall be done by buyer party.

 

Q. How do you make our business long-term and good relationship?

A: We provide our clients with one-stop service, from specific component to final assembled products, solving various problem for different clients all over the world.

Screw Sizes and Their Uses

Screws have different sizes and features. This article will discuss screw sizes and their uses. There are 2 main types: right-handed and left-handed screw shafts. Each screw features a point that drills into the object. Flat tipped screws, on the other hand, need a pre-drilled hole. These screw sizes are determined by the major and minor diameters. To determine which size of screw you need, measure the diameter of the hole and the screw bolt’s thread depth.

The major diameter of a screw shaft

The major diameter of a screw shaft is the distance from the outer edge of the thread on 1 side to the tip of the other. The minor diameter is the inner smooth part of the screw shaft. The major diameter of a screw is typically between 2 and 16 inches. A screw with a pointy tip has a smaller major diameter than 1 without. In addition, a screw with a larger major diameter will have a wider head and drive.
The thread of a screw is usually characterized by its pitch and angle of engagement. The pitch is the angle formed by the helix of a thread, while the crest forms the surface of the thread corresponding to the major diameter of the screw. The pitch angle is the angle between the gear axis and the pitch surface. Screws without self-locking threads have multiple starts, or helical threads.
The pitch is a crucial component of a screw’s threading system. Pitch is the distance from a given thread point to the corresponding point of the next thread on the same shaft. The pitch line is 1 element of pitch diameter. The pitch line, or lead, is a crucial dimension for the thread of a screw, as it controls the amount of thread that will advance during a single turn.
screwshaft

The pitch diameter of a screw shaft

When choosing the appropriate screw, it is important to know its pitch diameter and pitch line. The pitch line designates the distance between adjacent thread sides. The pitch diameter is also known as the mean area of the screw shaft. Both of these dimensions are important when choosing the correct screw. A screw with a pitch of 1/8 will have a mechanical advantage of 6.3. For more information, consult an application engineer at Roton.
The pitch diameter of a screw shaft is measured as the distance between the crest and the root of the thread. Threads that are too long or too short will not fit together in an assembly. To measure pitch, use a measuring tool with a metric scale. If the pitch is too small, it will cause the screw to loosen or get stuck. Increasing the pitch will prevent this problem. As a result, screw diameter is critical.
The pitch diameter of a screw shaft is measured from the crest of 1 thread to the corresponding point on the next thread. Measurement is made from 1 thread to another, which is then measured using the pitch. Alternatively, the pitch diameter can be approximated by averaging the major and minor diameters. In most cases, the pitch diameter of a screw shaft is equal to the difference between the two.

The thread depth of a screw shaft

Often referred to as the major diameter, the thread depth is the outermost diameter of the screw. To measure the thread depth of a screw, use a steel rule, micrometer, or caliper. In general, the first number in the thread designation indicates the major diameter of the thread. If a section of the screw is worn, the thread depth will be smaller, and vice versa. Therefore, it is good practice to measure the section of the screw that receives the least amount of use.
In screw manufacturing, the thread depth is measured from the crest of the screw to the root. The pitch diameter is halfway between the major and minor diameters. The lead diameter represents the amount of linear distance traveled in 1 revolution. As the lead increases, the load capacity decreases. This measurement is primarily used in the construction of screws. However, it should not be used for precision machines. The thread depth of a screw shaft is essential for achieving accurate screw installation.
To measure the thread depth of a screw shaft, the manufacturer must first determine how much material the thread is exposed to. If the thread is exposed to side loads, it can cause the nut to wedge. Because the nut will be side loaded, its thread flanks will contact the nut. The less clearance between the nut and the screw, the lower the clearance between the nut and the screw. However, if the thread is centralized, there is no risk of the nut wedgeing.
screwshaft

The lead of a screw shaft

Pitch and lead are 2 measurements of a screw’s linear distance per turn. They’re often used interchangeably, but their definitions are not the same. The difference between them lies in the axial distance between adjacent threads. For single-start screws, the pitch is equal to the lead, while the lead of a multi-start screw is greater than the pitch. This difference is often referred to as backlash.
There are 2 ways to calculate the pitch and lead of a screw. For single-start screws, the lead and pitch are equal. Multiple-start screws, on the other hand, have multiple starts. The pitch of a multiple-start screw is the same as its lead, but with 2 or more threads running the length of the screw shaft. A square-thread screw is a better choice in applications requiring high load-bearing capacity and minimal friction losses.
The PV curve defines the safe operating limits of lead screw assemblies. It describes the inverse relationship between contact surface pressure and sliding velocity. As the load increases, the lead screw assembly must slow down in order to prevent irreversible damage from frictional heat. Furthermore, a lead screw assembly with a polymer nut must reduce rpm as the load increases. The more speed, the lower the load capacity. But, the PV factor must be below the maximum allowed value of the material used to make the screw shaft.

The thread angle of a screw shaft

The angle between the axes of a thread and the helix of a thread is called the thread angle. A unified thread has a 60-degree angle in all directions. Screws can have either a tapped hole or a captive screw. The screw pitch is measured in millimeters (mm) and is usually equal to the screw major diameter. In most cases, the thread angle will be equal to 60-degrees.
Screws with different angles have various degrees of thread. Originally, this was a problem because of the inconsistency in the threading. However, Sellers’s thread was easier to manufacture and was soon adopted as a standard throughout the United States. The United States government began to adopt this thread standard in the mid-1800s, and several influential corporations in the railroad industry endorsed it. The resulting standard is called the United States Standard thread, and it became part of the ASA’s Vol. 1 publication.
There are 2 types of screw threads: coarse and fine. The latter is easier to tighten and achieves tension at lower torques. On the other hand, the coarse thread is deeper than the fine one, making it easier to apply torque to the screw. The thread angle of a screw shaft will vary from bolt to bolt, but they will both fit in the same screw. This makes it easier to select the correct screw.
screwshaft

The tapped hole (or nut) into which the screw fits

A screw can be re-threaded without having to replace it altogether. The process is different than that of a standard bolt, because it requires threading and tapping. The size of a screw is typically specified by its major and minor diameters, which is the inside distance between threads. The thread pitch, which is the distance between each thread, is also specified. Thread pitch is often expressed in threads per inch.
Screws and bolts have different thread pitches. A coarse thread has fewer threads per inch and a longer distance between threads. It is therefore larger in diameter and longer than the material it is screwed into. A coarse thread is often designated with an “A” or “B” letter. The latter is generally used in smaller-scale metalworking applications. The class of threading is called a “threaded hole” and is designated by a letter.
A tapped hole is often a complication. There is a wide range of variations between the sizes of threaded holes and nut threads, so the tapped hole is a critical dimension in many applications. However, even if you choose a threaded screw that meets the requisite tolerance, there may be a mismatch in the thread pitch. This can prevent the screw from freely rotating.

China Good quality 1850mm Track 13t Fuwa/BPW/York/Hj Commercial Truck Trailer Axle for Fuel Tank/Tanker Trailer   near me factory China Good quality 1850mm Track 13t Fuwa/BPW/York/Hj Commercial Truck Trailer Axle for Fuel Tank/Tanker Trailer   near me factory